specification control drawing 55a1141 four conductor cable, shielded, jacketed, general purpose, 600 volt 1-16-13 b this specifcation sheet forms a part of the latest issue of raychem specifcation 55a. jacket - radiation-crosslinked, modified etfe component wires - 55a0111 cable ratings and additional requirements title date revision shield - tin-coated copper cable construction details part number 1/ conductor size (awg) shield size (awg) jacket thickness (inches) outside diameter (inches) maximum weight (lbs/1000 ft.) minimum nominal nominal maximum 55a1141-30-* 30 38 .006 .008 .091 .104 7.7 55a1141-28-* 28 38 .006 .008 .098 .113 9.3 55a1141-26-* 26 38 .006 .008 .110 .127 12.1 55a1141-24-* 24 38 .006 .008 .123 .141 15.4 55a1141-22-* 22 38 .006 .008 .137 .159 19.7 55a1141-20-* 20 38 .006 .008 .154 .179 27.0 55a1141-18-* 18 38 .006 .008 .178 .208 37.7 55a1141-16-* 16 38 .006 .008 .198 .231 46.4 55a1141-14-* 14 38 .007 .009 .241 .282 69.1 55a1141-12-* 12 38 .007 .009 .284 .334 99.6 55a1141-10-* 10 38 .008 .010 .347 .408 154. 55a1141-8-* 8 34 .009 .011 .503 .593 291. temperature rating: 150c maximum continuous conductor temperature voltage rating: 600 volts (rms) at sea level accelerated aging: 300 3c for 7 hours blocking: 200 3c for 6 hours dielectric withstand: 1500 volts (rms), 60 hz flammability (procedure 1): 3 seconds (maximum); 3 in. (maximum); no faming of facial tissue jacket color: white preferred jacket elongation and tensile strength: elongation, 50% (minimum) tensile strength, 5000 lbf/in2 (minimum) jacket flaws: spark test, 1000 volts (rms) impulse dielectric test, 6.0 kv (peak) note: nominal values are for information only. nominal values are not requirements. life cycle: 200 3c for 168 hours low temperature-cold bend: -65 2c for 4 hours shield coverage: 85% (minimum) voltage withstand (post environmental): 1000 volts (rms), 60 hz, 1 minute part number: the * in the part numbers above shall be replaced by color code designators with a slash separating the component wire colors and a dash separating the component wire colors from the jacket color . colors shown do not necessarily refect the sequence of manufacturing. 1/ example: awg 22, black, brown, red and orange component wires; white jacket: 55a1141-22-0/1/2/3-9 users should evaluate the suitability of this product for their application. specifcations are subject to change without notice. tyco electronics corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specifcation, without notifcation to buyer. 1 / colors and color code designators shall be in accordance with mil-std-681. however, due to length limitations of the raychem part number, an alternative color code may replace mil-std-681 color code designators. (example: 901/902... may be replaced by axxx.) other codes and suffixes may be added to the part number as necessary, to capture any additional requirements imposed by the purchase order. page 1 of 1 raychem, te connectivity, te connectivity (logo) and te (logo) are trademarks. raychem wire & cable 501 oakside avenue redwood city, ca 94063-3800 phone: 1-800-227-8816 fax: 1-650-361-6297 dimensions are in inches, and unless otherwise designated are nominal. this specification sheet takes precedence over documents referenced herein. referenced documents shall be of the issue in effect on date of invitation for bid. ? 2005-2013 tyco electronics corporation. all rights reserved.
|
